收藏本站
Temperature Sensor and
System Monitor in a 10-Pin μMAX
UPPER BYTE
LOWER BYTE
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
11-BIT READ FORMAT
UPPER BYTE
LOWER BYTE
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
9-BIT READ FORMAT
Figure 5. Read Temperature Format
X = DON'T CARE
Alert Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex, expensive logic needed to be a bus
master. Usually the ALERT outputs of several slave
devices are wire-ORed to the same interrupt input of
the host master. Upon receiving an interrupt signal, the
host master can broadcast a receive byte transmission
(Figure 2) with the alert response address (0001 100).
A read operation is denoted by a 1 in the eighth
address bit. Then, any slave device that generated an
interrupt attempts to identify itself by putting its own
address on the bus.
The alert response can activate several different slave
devices simultaneously, similar to the I 2 C general call. If
more than one slave attempts to respond, bus arbitra-
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledge signal and continues to hold the interrupt
line low until serviced. The MAX6683 does not automat-
ically clear its ALERT when it responds to an alert
response address. The host master must then clear or
mask the ALERT by reading the Interrupt Status
Register, writing to the Interrupt Mask Register, or set-
ting bit 1 of the Configuration Register to zero before it
?
?
?
?
?
?
?
?
Bit 0 puts the MAX6683 into software standby mode
(STOP) or autoconvert (START) mode. The 2-wire
interface is still active in the standby mode. All volt-
age and temperature limits should be set before
setting this bit to 1.
Bit 1 enables and disables the ALERT output.
Setting this bit to 1 enables the ALERT output.
Bit 2 is reserved.
Bit 3 clears the ALERT output and stops the moni-
toring loop when set to 1. Clearing the output does
not affect the contents of the Interrupt Status
Registers.
Bit 4 sets the analog-to-digital conversion speed to
minimize interference from power-line frequencies.
Setting this bit to 1 can improve accuracy when the
power-line frequency is 50Hz. When the power-line
frequency is 60Hz, bit 4 should be zero.
Bit 5 reduces the oversampling ratio in the ADC
from 8 to 2. This reduces the monitoring cycle time
by a factor of 4 to typically 50ms at the cost of
reduced noise rejection.
Bit 6 is reserved.
Bit 7 resets all register values to their power-up
can identify other slaves generating an interrupt.
Command Byte Functions
The 8-bit Command Byte Register (Table 1) is the mas-
ter index that points to the other data, configuration,
limits, and address registers within the MAX6683. The
functions of those other registers are described below.
Configuration Byte Functions
The Configuration Register (Table 4) is a read-write reg-
ister with several functions:
default values. To reset all registers, set bit 7 to 1.
This also resets bit 7 to its power-up value of zero.
Read Temperature
The MAX6683 reads out temperature in an 8-, 9-, or 11-bit
two's complement format. To obtain the 8-bit temperature
data (7 bits plus sign), execute a Read Byte command to
the Temperature Data Register (address 27h).
To obtain the 11-bit temperature data (10 bits plus
sign), execute a Read Word command to the
Temperature Data Register (address 27h). When per-
12
______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX6969EVKIT+ KIT EVAL FOR MAX6969
MAX7500EVKIT+ KIT EVAL FOR MAX7500
MAX8630XEVKIT+ KIT EVAL FOR MAX8630X MAX8630W
MAX8678EVKIT+ KIT EVAL FOR MAX8678
MAX9635EVKIT+ KIT EVAL FOR MAX9635
MB-1390-DG BRACKET EXTERNAL MOUNT DARK GRY
MB3CG-S1 CORD GRIP 7.5-10.5MM DIAM
MB3CG-S2 CORD GRIP 10.5-15MM DIAM
相关代理商/技术参数
MAX6683EVSYS 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6684ESA 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6684ESA+ 功能描述:马达/运动/点火控制器和驱动器 Fan-Failure Detector RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6684ESA+ 制造商:Maxim Integrated Products 功能描述:DETECTOR FAN-FAILURE 6684 SOIC8 制造商:Maxim Integrated Products 功能描述:DETECTOR, FAN-FAILURE, 6684, SOIC8
MAX6684ESA+T 功能描述:马达/运动/点火控制器和驱动器 Fan-Failure Detector RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6684ESA-T 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6685AU40H 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6685AU40H+T 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor